tag:blogger.com,1999:blog-82387621538056331272024-03-19T00:31:24.850-07:00Online Manual SharingUnknownnoreply@blogger.comBlogger934125tag:blogger.com,1999:blog-8238762153805633127.post-25684774450005846422012-11-02T20:57:00.000-07:002012-11-02T20:57:00.669-07:002000 Dodge Dakota & Durango Power Windows ADJUSTMENTSRaise window fully, seating window in frame. Tighten bolts. Install door trim panel. TROUBLE SHOOTING POWER WINDOWS On Dakota, inspect circuit breaker No. 20 (20-amp) in junction block. On Durango inspect circuit breaker No. 21 (25-amp) in junction block. On all models, junction block is located on left end of instrument panel. Inspect fuse No. 9 (40-amp on Dakota, 50-amp on Durango) in Power Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-35494653585616753902012-11-02T20:56:00.000-07:002012-11-02T20:56:00.624-07:001999 Dodge Intrepid PRIMARY TIMING CHAIN And SPROCKETS REMOVAL AND INSTALLATION MANUAL1. Remove upper radiator crossmember. Disconnect fan assembly connector. Remove fan assembly. Remove drive belts. Using Crankshaft Pulley Holder (8191), hold crankshaft pulley and remove center bolt. Using a 3-jaw puller, remove crankshaft pulley. 2. Remove upper intake manifold. See INTAKE MANIFOLD . Remove electrical and vacuum harness retaining clips from valve cover studs. Remove ignition Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-89340395241658870422012-11-02T20:55:00.000-07:002012-11-02T20:55:00.389-07:002008 Ford Focus A/T Main Control Valve Body Removal And InstallationDisassembly 12 7Z490 Separator plate and gasket assembly Assembly 1. Install a new separator plate and gasket assembly. 2. NOTE: Do not fully tighten the bolts at this stage. Assemble the main control valve body and loosely install the bolts. DISASSEMBLY AND ASSEMBLY (Continued) 5. Install the solenoid body and loosely install the 6. Tighten the solenoid body bolts in the sequence bolts. shown. •Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-79887837606872264512012-11-02T20:54:00.000-07:002012-11-02T20:54:00.318-07:002008 Ford Focus A/T Main Control Valve Body Removal And InstallationDisassembly 12 7Z490 Separator plate and gasket assembly Assembly 1. Install a new separator plate and gasket assembly. 2. NOTE: Do not fully tighten the bolts at this stage. Assemble the main control valve body and loosely install the bolts. DISASSEMBLY AND ASSEMBLY (Continued) 5. Install the solenoid body and loosely install the 6. Tighten the solenoid body bolts in the sequence bolts. shown. •Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-39503546120731097572012-11-02T20:53:00.000-07:002012-11-02T20:53:00.309-07:002004 FORD F150 Door Window Glass-Rear SuperCrew REMOVAL AND INSTALLATION MANUALPart Steps 1. Remove the rear door trim panel. For additional Rear door window glass 1-4 information, refer to Section 501-00. Rear door window glass 1-7 regulator 2. Remove the rear door-mounted speaker. For additional information, refer to Section 415-00. NOTE: Some vehicles may use rivets to attach the glass to the regulator. 1. If removing only the rear door glass regulator assembly and Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-5422835888079397202012-11-02T20:52:00.000-07:002012-11-02T20:52:00.360-07:002000 Ford Ranger Cooling System Draining Filling and Bleeding Repair ManualNOTE: Less than 80% of the coolant capacity can be recovered with the engine in the vehicle. Dirty, rusty or contaminated coolant requires replacement. 1. Release the pressure in the cooling system by slowly turning the pressure relief cap one half to one turn counterclockwise to the first stop on the filler neck. When the pressure has been released, remove the pressure relief cap. 2. Raise and Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-88441758028476842972012-11-02T20:51:00.000-07:002012-11-02T20:51:00.666-07:002003 Ford F-Super Duty 250-550/ Excursion Rear Drive Axle/Differential/ Ford 10.50-Inch Ring Gear Installation Manual1. Remove the differential case. For additional information, refer to Differential Case in this section. 2. NOTE: The differential bearings need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, for additional information, refer to Differential Case in this section. NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-30618046369503391172012-11-02T20:50:00.000-07:002012-11-02T20:50:00.267-07:002000 Ford Crown Victoria/Grand Marquis Evaporator Core Housing Removal And Installation ManualFor additional information, refer to Section 414-01 . 2. Recover the refrigerant. For additional information, refer to Section 412-00 . 3. Drain the radiator so that the coolant level is below the heater core. For additional information, refer to Section 303-03 . 4. Raise the vehicle. For additional information, refer to Section 100-02 . 5. Remove the RH front wheel and tire. 6. Remove the screwsUnknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-5239020261557069342012-11-02T20:49:00.000-07:002012-11-02T20:49:00.316-07:001993 Ford Crown Victoria V8-281 4.6L SOHC Engine – Lean Driveability Symptoms ManualIf available, Service Bay Diagnostic System (SBDS) has a Manifold Absolute Pressure (MAP) sensor that can be used as a barometric pressure reference. Use “MAP/BARO” test under “Powertrain,” “Testers and Meters.” Ignore the hookup screen. Connect GP2 to the reference MAP on the following screen. 2. On a fully warmed up engine, look at Long Term Fuel Trim at idle, in Neutral, A/C off, (LONGFT1 and/Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-893386770101407802012-11-02T20:48:00.000-07:002012-11-02T20:48:00.775-07:001994 Ford Explorer FRONT WHEEL BEARINGS MANUALSee Fig. 1 . 2. Remove automatic locking hub assemblies. Remove snap ring and axle shaft spacer. Carefully pull plastic cam assembly from bearing adjusting nut. Remove 2 plastic thrust washers from adjusting nut. 3. Using magnet, remove locking key from spindle keyway. It may be necessary to rotate adjusting nut slightly to relieve pressure for locking key removal. Loosen adjusting nut with 2 3/8Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-33205616703328428092012-11-02T20:47:00.001-07:002012-11-02T20:47:35.542-07:001999 Ford Crown Victoria/ Grand Marquis Instrument Panel and Console Removal/ Installation ManualFor additional information, refer to Section 501-20B . 3. Close the glove compartment. 4. Position the speed control servo aside. 1. Disconnect the electrical connector. 2. Remove the nuts. 3. Position the speed control servo aside. 5. Disconnect the LH engine compartment in-line electrical connector. * Release the wiring harness locators. 6. Disconnect the brake fluid sensor electrical connectorUnknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-81173636749739792142012-11-02T20:46:00.001-07:002012-11-02T20:46:09.839-07:001998 Chevrolet Chevy K Pickup DTC P1626 Theft Deterrent Fuel Enable Signal Not Received Repair ManualAn intermittent may be caused by any of the following conditions: Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems. If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems. Test Description The number(s) below refer to the step number(s) on the diagnosticUnknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-16892425761758820562012-11-02T20:45:00.000-07:002012-11-02T20:46:06.482-07:002002 Chevrolet Impala Radiator Air Baffle and Deflector Replacement ManualRadiator Air Baffle and Deflector Replacement – Upper Removal Procedure 1. Remove the radiator air baffle retainers. 2. Tilt the rear of air baffle upward slightly. Slide the air baffle rearward in order to disengage the upper and lower clips of the air baffle from the fascia support. 3. Remove the radiator air baffle. Installation Procedure 2002 Chevrolet Impala 1. Position the radiator air Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-48139674189570352112012-11-02T20:27:00.000-07:002012-11-02T20:27:01.103-07:001997 Chevrolet Chevy K Pickup DTC P0152 HO2S Circuit High Voltage Bank 2 Sensor 1Important: Before clearing DTCs, use the scan tool in order to record the Freeze Frame and the Failure Records for reference. This data will be lost when the Clear DTC Information function is used. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? — Go to Step 2 Go to Powertrain On Board Diagnostic (OBD) System Check 2 1. Connect the scan tool. 2. Run the engine at the normal Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-38485447471381040322012-11-02T20:26:00.001-07:002012-11-02T20:26:54.526-07:002004 Chevrolet Silverado 1500 WHEEL HUB, BEARING, AND SEAL REPLACEMENT (4WD) MANUALView Of Retaining Bolts For Brake Hose And Wheel Speed Sensor Brackets Courtesy of GENERAL MOTORS CORP. 4. Remove the wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle. 2004 Chevrolet Silverado 1500 2004 SUSPENSION Front Suspension – Sierra & Silverado Fig. 63: Removing The Wheel Drive Shaft Nut Retaining Cover (4WD) Courtesy of GENERAL MOTORS CORP. IMPORTANT: Do Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-78609825562050942412012-11-02T20:25:00.000-07:002012-11-02T20:25:00.273-07:001994 Ford Thunderbird LX FUSES AND CIRCUIT BREAKERS MANUALThis information about 1994 Ford Thunderbird LX FUSES AND CIRCUIT BREAKERS MANUAL,inside of PDF manual is talking Circuit Breaker Windshield Wiper & Washer Pump, Interval Wiper 3 – Not Used 4 – 15 Amp Taillights, License & Parking Lights, Side Marker & Coach Lights, Cluster Illumination Lights, Radio & Clock Illuminator, A/C-Heater Illumination 5 – 15 Amp Turn Signal & Back-Up Lights, and more Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-80520525767812541612012-11-02T20:24:00.000-07:002012-11-02T20:24:00.265-07:00Service Manual 1989 Chevrolet Corvette V8-350 5.7Disassembly 1. Remove steering wheel as follows: a. Disconnect battery ground cable, then remove horn cap from steering wheel by pulling. b. Disconnect horn button wire, then remove telescope lever screws and shaft lock knob screw. c. Remove telescope adjustment lever, steering wheel nut retainer and nut. d. Remove steering wheel with a puller. 2. Remove spacer, bumper, spacer and snap ring Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-25458084790732554392012-11-02T20:23:00.000-07:002012-11-02T20:23:00.417-07:002005 Chevrolet Chevy K Silverado Disabling Auto Door Locks – keywords dic ipc lock manual mode operation program reprogram Repair ManualThere is no option to disable the auto door locks from the factory, but if an owner wishes to have the auto door locks disabled the following procedure can be performed: 1. Use the following procedure to disable the auto door locks on the models listed below: 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT 2007-2008 Chevrolet Avalanche, Silverado (new body style), Suburban, Tahoe Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-10889250410305241482012-11-02T20:22:00.000-07:002012-11-02T20:22:00.552-07:002004 Chevrolet Aveo SPARK PLUG REMOVAL AND INSTALLATION MANUALRefer to Spark Plug Wire Replacement . 4. Remove the spark plugs from the engine. Fig. 118: Identifying Spark Plug & Wire Courtesy of GENERAL MOTORS CORP. NOTE: Be sure plug threads smoothly into cylinder head and is fully seated. Use a thread chaser if necessary to clean threads in cylinder head. Cross- threading or failing to fully seat spark plug can cause overheating of plug, exhaust blow-by,Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-50336783510917589922012-11-02T20:21:00.000-07:002012-11-02T20:21:00.975-07:002004 Chevrolet Chevy K Silverado – 4WD Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement PickupEvaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement Pickup Removal Procedure Important Clean the evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the fittings in order to avoid possible system contamination. 1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 2. Remove the harness clip Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-47707385118636148472012-11-02T20:20:00.000-07:002012-11-02T20:22:10.663-07:001999 Chevrolet Silverado The service engine soon light is on with trouble code P1416 presentTests/Procedures: 1. Use a scanner and command the air pump on with the engine running at idle. Check if the O2 sensors go lean. 2. If the O2 sensor does not go lean on one bank, see if the check valve at the exhaust manifold is stuck closed, not allowing air into the manifold. Potential Causes: Defective Check Valve Diagnostic Codes: P1416 downloadUnknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-65839670387019814482012-11-02T20:19:00.000-07:002012-11-02T20:22:10.460-07:001998 Chevrolet Blazer Engine Oil Cooler Hose/ Pipe Removal And Installation ManualRemoval Procedure 1. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage. Important: Have a drain pan ready for the engine oil to drain into. 2. Remove the bolt attaching the engine oil cooler lines to the remote (frame mounted) oil filter adapter. 3. Remove and discard the seals. 4. Remove the engine oil cooler line retaining rings from the engineUnknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-38160770074341702862012-11-02T20:18:00.000-07:002012-11-02T20:18:00.610-07:002004 Audi A4 1.8 L Turbo FWD L4-1 fuel pump remove and install guideNote the rules for cleanliness. Attention: Note safety instructions disconnect the battery. Disconnect the battery ground (GND)-Gurt with the ignition switched off. Caution: Secure ground (GND) wire of the VAS5190 on an empty part of the chassis. Drag cone piece 2 shaft piece-1 - by VAS 5190. With electrical tape, apply a mark - arrow - on hose finally a = 1465 mm from the end of the suction hoseUnknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-89280317320061083662012-11-02T20:17:00.000-07:002012-11-02T20:17:00.832-07:002004 Audi A6 V6 2.7 L Turbo headlight remove and installationsNote: Use magnet if necessary, remove screw. B. separate multifunction harness connectors for headlamps. B. turn the headlights-2 - towards the middle of the vehicle and must remove from the housing front. Install-installation is the reverse distance, note the following adjust dimension - an - over plastic screw on new headlight. Note: Determine dimension - a - plastic bolt old headlamp, if Unknownnoreply@blogger.com0tag:blogger.com,1999:blog-8238762153805633127.post-25288894966754419882012-11-02T20:16:00.000-07:002012-11-02T20:16:00.943-07:002000 Audi A6 oil pan (A4 and A6) remove and install guideTo install oil pan (below), see INSTALLATION (lower oil pan - A4 & A6). (Lower oil pan - A4 & A6) installation 1 make sure that the oil pan gasket surfaces are clean and dry. Remove residual sugar sealant brush instead of a flat Bruiser from sump, if necessary with a hand drill and plastic. See to install fig. 99. seal. 2. Install you 2 screws diagonally related (in the pan to keep). Install the Unknownnoreply@blogger.com0