0 BlackBerry 7290 Wireless Handheld User Guide

This cell phones ebook contain 132 pages of wireless handheld user guide for BlackBerry 7290 Wireless Handheld™ Model Number: RAP40GW. Last modified: 13 September 2004 Part number: PDF-07783-001 Rev. 001 At the time of publication, this documentation complies with handheld software version 3.8. Check out the table of content for BlackBerry 7290 Wireless Handheld User Gu...

0 1973-74 Jensen-Healey Wheel Alignment Guide

JENSEN-HEALEY SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to manufacturers specifications given in owner's manual.CASTERIf caster angle is not to specifications, adjust length of strut rods by loosening both (front and rear) lock nuts. Caster angle is decreased by shortening rods and increased by lengthening rods. CAMBERCamber angle is not adjustable. If not to specifications, check suspension for wear or damage and replace components as necessaryTOE-INMeasure difference of distance between front of front tires and rear of front tires. If...

0 Honda Confirms NSX Concept

Good news to our NSX fans! The rumors are over the place and Honda confirms that they're building a new concept NSX car and it'll be unveiled on Detroit Auto Show on January 9, 2012.The Next Honda NSX Concept Car?On topgear.com .... Yoshikazu Kigoshi told Top Gear that the company "needs a halo car", a decision that has come straight down from Honda president Takanobu Ito. "A new S2000 is a difficult car for us to do," Kigoshi-san told us, "because of its front-engined rear-drive platform. But we are definitely looking at the EV-ster and a new NSX."Not much detail on this car, but surely it will have a Mid-engine and it will get the...

0 1974 Jaguar Wheel Alignment Guide

JAGUAR SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to owner's manual for manufacturer's specifications.RIDING HEIGHTXJ6 & XJ12 (Front) - Check that vehicle is full of gasoline oil and water, and that tires are properly inflated. Press down on front bumper and slowly release, then lift up on bumper and slowly release, this will settle front suspension. Measure distance between center of headlight and ground on both sides of vehicle. Correct height should be 24.6" (611 mm) minimum. To adjust, install or remove spring spacers from front...

0 1973 Jaguar Wheel Alignment Guide

1973 JAGUAR SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to owner's manual for manufacturer's specifications.RIDING HEIGHTXJ6 (Front) - Vehicle should be loaded with sufficient weight to equal driver, three passengers and ten gallons of gasoline, or 850 lbs.XJ6 (Rear) - Set rear riding height using two setting links (Churchill No. J25). Hook link into lower hole of rear mounting and depress body until end of tool can be slid over the hub carrier fulcrum nut.XJ12 (Front) - With vehicle full of gasoline, water and oil, press downward on front...

0 1962-72 Jaguar Wheel Alignment

1962-72 JAGUAR SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, ensure tires are properly inflated.RIDING HEIGHTMk II, 3.8 and Mk 10 Front - Vehicle should be in unloaded condition with full tank of gas.Mk II Rear - Vehicle should be in unloaded condition with full tank of gas.FRONT SUSPENSION SETTING LINKS3.8, 420 Series, Mk 10, XKE 3.8, XKE 4.2 AND XJ6 Rear - Set rear riding height using two setting links (Churchill No. J25). Hook link into lower hole of rear mounting and depress the body until other end of tool can be slid over hub carrier fulcrum nut.420 and 420 G Front - Place block...

0 1976 Fiat Honda Jaguar Wheel Alignment Guide

FIATModel X1/9 Front and Rear - Camber is nonadjustable. If not within specifications, inspect suspension for damage and repair or replace parts as necessary.TOE-INModel 128, 131 and X1/9 Front - Place front wheels in straight-ahead position. If toe-in is not within specifications, loosen sleeve locking nut on tie rods. To adjust, rotate hexagon on ball pin to set toe-in to specifications. Hold hexagon in position and lock nut against tie rod sleeve.Model 128 Rear - If rear toe-in is not within specifications raise rear of vehicle and compress one end of leaf spring, shifting it from flexible guide anchoring spring to control arm. Remove guide...

0 1975 Honda Wheel Alignment Guide

HONDA SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before checking or adjusting wheel alignment, make sure tires are correctly inflated. Refer to manufacturers specifications located in glove boxRIDING HEIGHTMake sure tires are properly inflated. Measure from bottom of side marker lamps to ground. If height measurement is not within specifications, check rear height before attempting to repair front suspensionCASTERCaster is nonadjustable. If alignment is not within specifications, inspect for damaged parts and replace as necessary.CAMBERCamber is nonadjustable. If alignment is not within specifications, inspect for damaged parts and replace...

0 1974 Honda Wheel Alignment Guide

HONDA SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before checking or adjusting wheel alignment, make sure tires are correctly inflated. Refer to manufacturers specifications located in glove box.RIDING HEIGHTMake sure tires are properly inflated. Measure from bottom side marker lamps to ground. This distance should be 25.78" in front and 24.01" in rear. NOTE - If height measurement is not within specifications, check rear height before attempting to repair front suspension.CASTERCaster is nonadjustable. If alignment is not within specifications, inspect for damaged parts and replace as necessary.CAMBERCamber is nonadjustable. If alignment...

0 BlackBerry 7130 Series Smartphone User Guide

This smartphone user guide is created for BlackBerry 7130 Series. Contains 242 Pages, this e-book table of content explains all kind of BlackBerry Smartphone devices from its basics manual information, blackberry shortcuts, applications, security, service books, to BlackBerry basics troubleshooting.BlackBerry basics 9 About typing input methods 9 Type text using SureType technology 9 Type text using multi-tap 9 Switch typing input methods 9 Switch applications 10 Assign an application to a Convenience key 10 Set owner information 10 About links 10 Create a link for a PIN 10 Expand a folder 11 Collapse a folder 11 BlackBerry basics shortcuts 11...

0 1975 Fiat Wheel Alignment Guide

FIAT SPECIFICATIONS AND ADJUSTMENTTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to manufacturers specifications given in owner's manual.CASTERModel 131 and 128 (Except. Sport L) - If caster is not to specifications, raise front of vehicle. Remove stabilizer bar-to-control arm nut and disconnect control arm from body. Remove end of stabilizer bar from control arm. To adjust caster, addition of shims between end of stabilizer bar and rubber pad of control arm will decrease caster angle and removal of shims will increase caster angle. Reverse removal procedure and recheck...

0 1963-73 Fiat Models Wheel Alignment Guide

1963-73 FIAT SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, ensure that tires are inflated according to specificationsCASTERModel 128 - If caster is not within specifications, raise front of vehicle. Remove anti-roll bar to control arm nut and disconnect control arm from body. Remove end of anti-roll bar from control arm. To adjust caster, addition of shims between end of anti-roll bar and rubber pad of control arm will decrease caster and removal of shims will increase caster. Reverse removal procedure and check caster.Model 124 - If caster is not within specifications, raise front of...

0 1974-75 Nissan Datsun Wheel Alignment Guide

DATSUN SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, make sure that tires are properly inflated. Refer to manufacturer's specifications given in owner's manual.RIDING HEIGHTPickup Only - Measure distance from center of lower control arm bushing (where it connects to body) and lower steering knuckle bushing (see illustration). To adjust, raise vehicle to release tension on anchor bolt adjusting nut and turn anchor bolt to adjust to specified height.             Riding Height SpecificationsApplication                ...

0 1962-72 Nissan Datsun Wheel Alignment Guide

1962-72 DATSUN SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, ensure that tires are properly inflated.RIDING HEIGHTPickups Only - Adjust to specificied distance by turning anchor bolt adjusting nut. Raise vehicle to release tension on adjusting nut.Riding Height Measuring PointCASTERAll Models (Except 240Z, 510 and 1200) - Caster is adjusted by increasing or decreasing the thickness of shims inserted between upper link spindle and upper link mounting bracket. When front shim thickness increases, caster reduces. Set caster to specifications given in table. NOTE - Do not adjust caster with...

0 1971-72 Cricket Wheel Alignment Guide

1971-72 CRICKET SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATIONBefore attempting to check or adjust front wheel alignments, ensure tires are properly inflated. Manfucturer recommended tire pressure is stenciled on inside of glove box door.CASTERCaster is not adjustable. If alignment is not within specification, inspect for damage parts and replace as necessary.CAMBERCamber is not adjustable. If alignment is not within specifications, inspect for damaged parts and replace as necessary.TOE-INTo adjust toe-in, loosen ball joint lock nuts on both tie rods. Loosen screws in rubber boot on inner ends of tie rod and ensure boots are free. Adjust tie rods...

0 1972-76 Courier All Models Wheel Alignment Guide

1972-73 COURIER SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATIONBefore attempting caster or camber adjustments, ensure tires are correctly inflated. Specifications are located on glove box door; especially consider radial tires, they require a different pressure than conventional tires.NOTE - For reliable vehicle control, maintain specified difference between front and rear tire pressure.NOTE - Vehicle must be unloaded, except fuel, water, and oil should be at their proper levels.CASTERTo correct caster, adjust shims between upper control arm and frame or turn control arm shaft until correct angle is obtained (see specifications).CAMBERThe camber...

0 1971-75 Colt All Models Wheel Alignment

COLT SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, ensure that tires are properly inflated. Refer to specifications in owners handbook.CASTERCaster is nonadjustable. If not within specifications, check front suspension for damage. Repair or replace parts as necessary.CAMBERCamber is nonadjustable. If not within specifications, check front suspension for damage. Repair or replace parts as necessary.TOE-INPosition wheels in straight-ahead position. If toe-in is not within specifications, loosen locking nuts on tie rod turn buckels. To adjust, rotate turn buckels until toe-in is within specifications....

0 1974 Capri Wheel Alignment

CAPRI SPECIFICATIONS AND ADJUSTMENTTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, make sure that tires are properly inflated. Refer to manufacturers specifications, located inside glove box door.CASTERAll Models - Caster is nonadjustable. If not within specifications, check front suspension for damage. Repair or replace parts as necessary.CAMBERAll Models - Camber is non adjustable. If not within specification, check front suspension for damage. Repair or replace parts as necessary.TOE-INAll Models - Position wheels in straight-ahead position and loosen tie rod end lock nut and clips securing bellows. To adjust toe-in,...

0 1970-73 Capri All Models Wheel Alignment

1970-73 CAPRI SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, ensure that tires are properly inflated. Refer to manufacturers specifications located on right hand sun visor.CASTERAll Models - Caster is nonadjustable. If not within specifications, check front suspension for damage. Repair or replace parts as necessary.CAMBERAll Models - Camber is non adjustable. If not within specifications, check front suspension for damage. Repair or replace parts as necessaryTOE-INAll Models - Position wheels in straight ahead position and loosen tie rod end lock nut and clips securing bellows. To adjust...

0 1976 Import Models Wheel Bearing Adjustment Guide

ARROW AND COLTAll Models - Tighten adjusting nut to 14.5 ft. lbs. After seating bearing components, loosen nut to 0 ft. lbs. Now make final adjustment to 3.6 ft. lbs. After installing lock cap, insert cotter pin. NOTE - Do not loosen adjusting nut more than 15 degrees to align spindle holes.AUDINOTE - The following procedure can only be performed using special tools indicated.Model 100 (Front) - 1) Raise and support front of vehicle. Remove lower wheel bolt and replace with special wheel bolt adapter (V-104) and special dial indicator (G-43). By means of retaining screw on special tool (V-104), adjust dial indicator to pretensioned position of...

0 1975 BMW Models Wheel Alignment Guide

BMW SPECIFICATIONS AND ADJUSTMENTSTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, ensure tires are properly inflated. The 2002 series requires 26 psi front and rear. The 3.0 series require 30 psi front and rear. The 530i series requires 28 psi front and 26 psi rear.CASTER AND CAMBERAll Models - Before checking caster and camber, vehicle must be in loaded condition. Loaded condition consists of two 143 lbs. weights on front seat, one 143 lbs. weight on rear seat, gas tank full and 66 lbs. on left side of luggage compartment. If caster and camber are not within specifications check suspension for damage. Repair or replace...

0 1976 Import Models Wheel Alignment Guide

BMWADJUSTMENTTIRE INFLATION (COLD)Before attempting to check or adjust wheel alignment, ensure tires are properly inflated. The 2002 series requires 26 psi front and rear. The 3.0 series requires 30 psi front and rear. The 530i series requires 28 psi front and 26 psi rear.CASTER AND CAMBERAll Models - Before checking caster and camber, vehicle must be in loaded condition. Loaded condition consists of two 143 lbs. weights on front seat, one 143 lbs. weight on rear seat, gas tank full and 66 lbs. on left side of luggage compartment. If caster and camber are not within specifications check suspension for damage. Repair or replace parts as necessary.TOE-INAll...