Thursday, January 12, 2012

0 Mazda 1974-76 Models Wheel Alignment Repair Guide

MAZDA SPECIFICATIONS AND ADJUSTMENTS

TIRE INFLATION (COLD)
Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to manufacturer's specifications given in owner's manual.

CASTER
808, RX2 & RX3 MODELS - Caster is not adjustable. If caster angle is not to specifications, inspect suspension for wear or damage and repair or replace components as necessary.

RX4 - Caster and camber angles can be adjusted by changing position of the shock absorber support. To adjust remove four nuts attaching shock absorber support to fender apron. Raise front of vehicle and support with jack stands, then remove wheel on side to be adjusted. Press shock absorber downward and change position of support according to following table and illustration. Tighten shock absorber support attaching nuts. Install wheel, lower vehicle and recheck caster and camber angles.


Pickup - To adjust, change shims between upper arm shaft and support bracket or turn upper arm shaft until specifications are obtained.


CAMBER

808, RX2, and RX3 - Camber is not adjustable. If camber angle is not to specifications, inspect suspension for wear or damage and repair or replace components as necessary.

RX4 - See procedure given under Caster adjustment.

Pickup - To adjust, change shims between upper arm shaft and support bracket until specifications for camber are within limits.

TOE-IN
All Models - Position wheels to center position and loosen tie rod locking nuts at each end of tie rod. Check that tie rod ends are in the same position on each rod ensuring that the tie rods are the same length. Turn tie rods by equal amounts until the toe-in is within specifications. Tighten locking nuts.



0 LUV 1974-76 Wheel Alignment Repair Guide

LUV SPECIFICATIONS AND ADJUSTMENTS
TIRE INFLATION
Before checking or adjusting wheel alignment, ensure tires are correctly inflated. Refer to manufacturers specifications located in glove box or an right hand door jam.

RIDING HEIGHT
1) Place vehicle on smooth level surface. Bounce vehicle several times. Raise vehicle and allow to settle at normal height6. Measure distance as shown in illustration.


NOTE - Height check should be made with a full tank of gas, spare tire installed, and jack included. No passengers should be in vehicle.

2) Difference between measurements of each side must not be more than 1/2". If an adjustment is necessary, it can be made at bolt on height control arm

Riding Height Specifications
Front - 4.6"
Rear - 7.4"

CASTER
Adjustment is made with shims inserted between upper control arm pivot shaft and frame. Adding or subtracting shims from either front or rear bolts will effect a change in caster. Shims may not be transfered from front to rear or from rear to front. Transfer of one shim from front bolt to rear bolt will decrease positive caster. For correct specifications, refer to table

CAMBER
Camber is adjusted by adding or subtracting shims. Adding on equal number of shims at both front and rear of pivot shaft will decrease positive camber. For correct specifications, refer to table.

TOE-IN
NOTE - Toe-in must be adjusted after caster and camber adjustment.

Toe-in can be adjusted by rotating the intermediate rod after loosening lock nuts. Rotating intermediate rod towards front of vehicle reduces toe-in and towards rear of vehicle increases toe-in. For correct specifications, refer to following guide table.


Friday, January 6, 2012

0 Volvo 1975 Models Wheel Alignment Guide

VOLVO SPECIFICATIONS AND ADJUSTMENTS

TIRE INFLATION (COLD)
Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to manufacturers specifications given in owner's manual.

CASTER
164 Series - If caster not within specifications, loosen bolts at upper control arm shaft using suitable tool (SVO 2713). Increase caster angle by adding shims at rear bolt or by removing shims from front bolt. To decrease caster angle, remove shims at front bolt or add shims to rear bolt. Tighten bolts and recheck caster angle.

240 Series - If caster is not within specifications, loose nuts at strut assembly upper attachment. Use a special tool (9995038) at strut upper attachment to adjust caster to specifications, then tighten nuts and recheck caster.

CAMBER
164 Series - If camber not within specifications, loosen bolts at upper control arm shaft using suitable tool (SVO 2713). To increase camber angle, remove equal amount of shims from front and rear bolts. To decrease camber angle, add shims to front and rear bolts in equal amounts. Tighten bolts and recheck camber angle.

240 Series - See 240 Series procedure under Caster adjustment.

TOE-IN
All Models - Place wheels in straight-ahead position and loosen lock nuts on steering links (tie rods). To adjust toe-in rotate adjustable sleeves until correct toe-in is obtained. Tighten lock nuts and recheck toe-in.


0 Volvo 1974 Wheel Alignment Guide

TIRE INFLATION (COLD)
Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to manufacturer's specifications given in owner's manual.

CASTER


All Models - If caster is not within specifications, loosen bolts at upper control arm shaft using suitable tool (SVO 2713). Increase caster angle by adding shims at rear bolt or by removing shims from front bolt. To decrease caster angle, remove shims at front bolt or add shims to rear bolt. Tighten bolts and recheck caster angle.

CAMBER


All Models - If camber is not within specifications, loosen bolts at upper control arm using suitable tool (SVO 2713). To increase camber angle, remove equal amount of shims from front and rear bolts. To decrease camber angle, add shims to front and rear bolts in equal amounts. Tighten bolts and recheck camber angle.

TOE-IN


All Models - Place wheels in straight-ahead position and loosen lock nuts on steering links (tie-rods). To adjust toe-in, rotate adjustable sleeves until correct toe-in is obtained. Tighten lock nuts and recheck toe-in.


0 Volvo 1963-73 Wheel Alignment Guide

1963-73 VOLVO SPECIFICATIONS AND ADJUSTMENTS

TIRE INFLATION (COLD)
Before attempting to check or adjust wheel alignment, ensure that tires are properly inflated.


CASTER
Model 544 - If caster is not within specifications, loosen clamp bolt securing eccentric bushing located on upper control arm. Using suitable tool (SVO 1411 or SVO 2201) turn the eccentric bushing. One complete turn alters caster by 1/2 degrees.
NOTE - If camber is correct, one complete turn of eccentric must be completed to eliminate camber change. Tighten clamp bolt and recheck caster.

160 Series and 140 Series - If caster not within specifications, loosen bolts at upper wishbone shaft using suitable tool (SVO 2713). Increase caster by adding shims at rear bolt or by removing shims from front bolt. To decrease caster, remove shims at front bolt or add to rear bolt. Tighten bolts and recheck caster.

P1800 Series - Check caster and camber. If caster is not within specifications and camber is correct, adjust caster as follows.
Raise vehicle and support under body at jacking points. Loosen front axle member attaching bolts. To correct caster, add or remove shims between front axle member and side member. Some amount of change must be done on both sides of vehicle to avoid undue strain on front axle member. Tighten bolts and recheck camber.
If caster is not within specifications and camber is incorrect adjust caster as follows:
Bend up locking plate for bolts at upper control arm shaft and loosen bolts. Increase caster by adding shims to rear bolt or by removing shims from front bolt. To decrease caster, remove shims from rear bolt or add to front bolt. Tighten bolts and recheck caster. If caster is within specifications, lock bolts with locking plate.

CAMBER
Model 544 - If camber is not within specifications, loosen clamp bolt securing eccentric bushing located on upper control arm. Using suitable tool (SVO 1411 or SVO 2201) turn the eccentric bushing to change camber. NOTE - Altering camber also means a slight alteration of caster, but amount of negligible. Tighten clamp bolt and recheck camber.

160 Series & 140 Series - If camber is not within specifications, loosen bolts at upper wishbone shaft using suitable tool (SVO 2713). To increase camber, remove equal amounts of shims from front and rear bolt. To decrease camber, add shims to front and rear bolt in equal amounts. Tighten bolts and recheck camber.

P1800 Series - If camber is not within specifications, bend up locking plate and loosen bolts at upper control arm shaft. To increase camber, decrease amount of shims and add shims to decrease camber. Shims of same thickness must be added or removed to both attaching bolts or caster will be affected.
NOTE - On 1972-73 models, total thickness of shims at each bolt may not exceed .48" (12.2 mm) and difference in thickness between shims at front and rear may not exceed 0.1" (2.54 mm). Tighten bolts and recheck camber. If camber is within specifications, lock bolts with locking plate.

TOE-IN
All Models (1963-73) - Place wheels in straight ahead position and loosen lock nuts (late models) or clamping bolts (early models) on tie rod. To adjust toe-in to specifications, rotate tie rod. Tighten lock nuts or clamping bolts and recheck toe-in.


Tuesday, January 3, 2012

0 Quick Start Guide for Outlook for PC monitor

Outlook for PC monitor is the software you need to download to the computer.
• There is access to the Outlook client configured for always.
• The maintain a reliable Internet connection.
The instructions here are helps PC monitor Outlook configuration. Can configure software to support a single user only.

This quick start guide will help you.
-The system requirements.
Install-PC monitor.
Configure the Outlook-PC monitor.
-The next step
System requirements
You must run the PC monitor Outlook requirements: PC:
• The supported Windows operating system.
o Microsoft Windows 2000 Professional sp4
o Microsoft Windows XP Professional SP1 or later
• Hardware requirements
o 128 MB of RAM
o 128 MB of hard drive space
• Software requirements
o Internet Explorer 5.0 or higher
o version of the Microsoft Outlook client support
° Outlook 2000
° Outlook XP (SP2 only)
° Outlook 2003
Note: without being prompted user credentials have Outlook open.
• Windows account information
need permission to install a Windows user PC software o login

Configure Outlook for PC monitor.
(Calendar, contacts, tasks, and notes) is the time to setup the monitor of the PC for Outlook can start now your email and PIM to receive is because of it's data from a Microsoft Outlook client.
Please check the following.
• Logged in as the user can be installed in the PC monitor machine and configure the software.
• Are you having to enter username and password to open the Outlook client.
• Local, as the Outlook the default e-mail delivery location is configured to use a PST file.

Download

0 Volkswagen 1976 Wheel Alignment Guide

ADJUSTMENT

TIRE INFLATION (COLD)
Before attempting to check or adjust wheel alignment, make sure tires are properly inflated. Refer to manufacturers specifications given in owner's manual.

CASTER
Caster angle is part of front axle design and is not adjustable. If not within specifications, inspect front suspension for wear or damage and replace or repair components as necessary.

CAMBER
Type 1 and 2 (Front) - Camber is adjusted by an eccentric bushing. Loosen nut on upper torsion arm, then rotate eccentric bushing until specified camber angle is obtained. NOTE - Basic setting is with eccentric notch facing in forward position. Adjustment must be made within 90 degrees either direction.

Dasher (Front) - If adjustment is necessary, loosen nuts at attaching ball joint to track control arm. To adjust, insert suitable adjusting tool (40-200) in adjusting holes in control arm and pry ball joint sideways until camber is set to specifications. NOTE - Difference in camber between wheels should not vary more than 1 degrees. Tighten attaching nuts and recheck camber.

NOTE - On dasher models, insert tool from on right side and from rear on left side.

Rabbit and Scirocco (Front) - If adjustment is necessary, loosen nuts of suspension strut-to-wheel bearing housing mounting bolts. Turn eccentric bolt (upper mounting bolt) until specified camber angle is obtained. Tighten mounting bolt nuts and recheck camber angle.

Type 1 (Rear) - Camber angle is dependent on torsion bar adjustment. If camber angle is not within specifications, see Torsion Bar Adjustment.

Type 2 (Rear) - If minor adjustment is necessary, loosen bolts attaching bearing housing to spring plate and diagonal arm. Adjust by changing position of bearing housing in elongated holes in spring plate. Tighten bolts and recheck camber. NOTE - Range that this procedure will cover is very small.

Dasher, Rabbit and Scirocco (Rear) - Rear camber is not adjustable. If camber angle is not to specifications, inspect rear suspension for wear or damage and repair or replace components as necessary.

TOE-IN
Type 1 ( Front) - Working on inner end of tie rod, bend up lockplate. Loosen lock nut and clamp bolts from tie rods. Top tapered rings from inn er end of right side tie rod. Rotate tops of tie rods. Forward rotation increases toe-in; rearward rotation decreases toe-in. When specified to is achieved, placte tie rods so ball joints are not angled. Tighten clamp bolts and lock nuts. If steering wheel is centered after making adjustment, use Fig. 1 to recenter steering wheel. NOTE - Centering steering wheel will not alter toe-in
Fig. 1 Direction of Tie Rod Rotation to Align Steering Wheel (Type 1 Only)



Type2 (Front) - 1) Right side tie rod adjust front wheel toe. Press drag link off steering drop arm. Place left side wheel in straight-ahead position. Adjust right side tie rod until specified to is obtained.
2) Place steering gear so protrusion on dust cap is properly aligned. Attach drag link to drop arm. Drag link must enter mounting with no tension against it. Readjust drag link if necessary.

Dasher, Rabbit, Scirocco (Front) - Place front wheels in straight-ahead position. Loosen lock nut on adjustable tie rod end (left side, Dasher; right side, Rabbit and Scirocco). Hold axle boot to avoid twisting. Adjust right side tie rod until specified toe-in.

Type 1 (Rear) - If adjustment is necessary, remove nuts securing spring plate but do not remove bolts. To adjust, move diagonal arm forward or backward in slotted spring plate mounting holes.until toe-in is set to specifications. Install spring plate attaching nuts and recheck toe-in.

Type 2 (Rear) - If adjustment is necessary, loosen bolts attaching bearing housing to spring plate and diagonal arm. Change position of bearing housing in elongated holes on spring plate. Tighten bolts and recheck toe-in.

All Other Models (Rear) - Toe-in is not adjustable. If toe-in is not within specifications, inspect rear suspension for wear or damage and repair or replace components as necessary.

TORSION BAR ADJUSTMENT (REAR)
Type 1 - Using a suitable protractor, find deviation of vehicle from horizontal plane and note reading which will be used in setting angle of spring plate. Install spring plate on torsion bar and measure position with protractor. If not within specifications, adjust by moving torsion bar, one spline at a time, forward or backward until correct position is obtained.

Type 2 - Using a suitable protractor, check horizontal position of vehicle on one frame side member. Reading should be noted; it will be used in setting spring plate angle. Insert inner end of torsion bar in center anchor and pres spring plate on outer end of torsion bar. Adjust protractor on unloaded spring plate until bubble is in center position.  Adjust torsion bar one spline forward or rearward until correct specifications are obtained.



 

2012 BY ManualTransformerOnline Manual Sharing